Payment & Shipping Terms:
|Matrial:||Alloy Steel||Standard:||GB, ASTM, DIN,JIS|
|Length:||Below 16 Meters||Shape:||Round Bar|
|Techniques:||Cold Drawn; Hot Rolled; Cold Rolled; Forged||Surface:||Black, Bright, Polished, Peeled, Or Upon Request|
|Ultrasonic Test:||100% UT Passed||Processing:||Annealed Or Quenched And Tempered Provided|
|End:||Beveled, Plain End As Required||Quality Inspection:||SGS, BV Etc.|
|Service:||Cutting Service And 3rd Party Inspection Is Provided|
Forged Round Bar,
Forged Steel Bars,
Forged Steel Round Bars
AISI 1020 Mild Carbon Low Tensile Steel Bar Forging 130-1600mm
AISI 1020 is a low hardenability and low tensile carbon steel with Brinell hardness of 119 – 235 and tensile strength of 410-790 MPa. It has high machinability, high strength, high ductility and good weldability. It is normally used in turned and polished or cold drawn condition. Due to its low carbon content, it is resistant to induction hardening or flame hardening. Due to lack of alloying elements, it will not respond to nitriding. However, carburization is possible in order to obtain case hardness more than Rc65 for smaller sections that reduces with an increase in section size. Core strength will remain as it has been supplied for all the sections. Alternatively, carbon nitriding can be performed, offering certain benefits over standard carburizing.
AISI 1020 steel can be largely utilized in all industrial sectors in order to enhance weldability or machinability properties. It is used in a variety of applications due to its cold drawn or turned and polished finish property.
Applications of 1020 Mild Steel
AISI 1020 steel is used in case hardened condition. The applications of AISI 1020 steel are:
- It is used for simple structural application such as cold headed bolts.
- AISI 1020 steel also finds use in the following components:
-Dimension: Diameter 4-1600 mm, any length below 16 meters
Cold drawn: 4-100 mm
Peeled: 30-160 mm
Grinded: 4- 600 mm
Turned: 130-1200 mm
Hot rolled: 12-320 mm
Hot forged: 130-1600 mm
- EAF+(ESR) or EAF+LF+VD+(ESR)
- HOT rolled; Cold rolled; Forged; Cold Drawn
- Heat Treatment: Untreated, Annealing, N+T, Q+T
- Smelting: EAF+LF+VD (+ESR)
- Surface Finish: Black, Rough Machined, Peeled, Turned or upon request
- UT 100% passed
- Cutting service provided
- Third Party inspection is acceptable (SGS, BV etc.)
AISI 1020 Grades Equivalency
|1020||C22 / CK22||S20C||20||C20E4|
Chemical Requirements, Composition, %
|AISI 1020||0.17-0.23||0.30–0.60||0.040 max||0.050 max||No Requirement|
|Standard||Steel Grade||Yield strength MPa (>=)||Tensile strength MPa (>=)||
Below inspection will be done in the production.
(1) ray detection---RT;
(2) ultrasonic testing---UT;
(3) Magnetic Particle Testing-MT;
(4) penetration testing-PT;
(5) eddy current flaw detection-ET
Fabrication and Heat Treatment
In the cold drawn or turned and polished condition, AISI 1020 steel has high machinability. As per recommendations of machine manufacturers, AISI 1020 steel can be used for drilling, turning, milling and tapping operations using suitable feeds, tool type and speeds.
AISI 1020 can be welded by performing the most common welding processes. In the cold drawn or turned and polished condition, it has better weldability. It has been suggested that the welding process should not be performed in heat treated or carburized condition.
AISI 1020 steel is heated at 870°C - 910°C followed by holding for certain time until the temperature remains constant all over the section. It is then cooled in a furnace.
AISI 1020 is heated to between 880°C - 920°C in a suitable carburizing atmosphere followed by holding for sufficient amount of time to produce the needed carbon content and case depth. After this, refining/hardening and tempering processes are carried out to optimize the core and case properties.
AISI 1020 steel is slowly cooled and re-heated at 870°C - 900°C followed by holding until the temperature remains constant all over the section and quenching in water, oil or brine.
After performing the core refining process, it is re-heated to 760°C - 780°C followed by holding until the temperature is consistent all over the section. It is then quenched in water.
AISI 1020 steel is re-heated at 150°C - 200°C followed by holding for certain time until the temperature remains constant throughout the section. It is soaked for 1 hour per 25 mm of section and then cooled under normal atmosphere. By performing the tempering process, the toughness of the case will be improved and grinding cracks will be reduced.
AISI 1020 steel is heated at 890°C - 940°C followed by holding until the temperature remains constant throughout the section. It is soaked for 10 - 15 minutes and then cooled in still air.
AISI 1020 steel is heated to 650°C - 700°C followed by holding until the temperature remains constant all over the section and soaking for 1 hour per 25 mm of section. It is then cooled in still air.
What we can offer?
-We offer a wide range of steel products in a wide variety of dimensions and executions, according to the common international specifications or customize.
-Machining and heat treatment are available.
-Also, we advise you in choosing the right materials.
OUR MAIN PRODUCTS ARE LISTED AS BELOW
-Round: Dia. 4 -1600 mm
-Flat: T. 10-120 mm x W. 60-810 mm
-Block: T. 80-1200 mm x W. 100-1600 mm
PAYMENT AND SHIPPING
1. Both T/T and L/C will be acceptable
2. Trade Terms: FOB, CIF, CFR
3. The delivery will be in 10-15 days if have stock; For customized items, the delivery will be negotiated by both parties
4. Shipping by sea freight from Shanghai Port (PRC) for Bulk orders, by airfreight or express for samples
Shanghai Unite Steel Trading Co., Ltd
We are committed to integrate engineering steel resources in china and serve the global engineering steel market. Our company has more than 15 years of experience in steel researching, production, managing and sales. And our team mostly are based on and worked in national famous steel enterprise.
In the aspect of resources and information, we have established cooperative and stronger relationship with nearly hundred enterprises, either state-owned or private owned in china.
What’s more, we have built long, deep and close business relationship with dozens of steel company, Sharing and holding equities with several steel enterprises. Because of the close cooperation with steel companies and our pioneering spirit, which can ensure us stay at the top competition, and ensure our customers get what they really want!
Q: Are you a manufacturer or merely a trader?
A: We are group of companies and owned manufacturer bases and trading company. We specialized in special steel which include alloy structural steel and carbon steel and stainless steel, etc. All material are with high quality and competitive price.
Q: How do you guarantee the quality of your product?
A: Firstly, we can provide the certificates from the third party, such as TUV, CE, if you need. Secondly, we have a complete set of inspection system and every process is checked by QC. Quality is the lifeline of enterprise survival.
Q: Delivery time?
A: We have ready stock for most of material grades in our warehouse. If the material doesn't have stock, the delivery lead time is about 5-30 days after receiving your prepayment or firm order.
Q: What is the payment term?
A: T/T or L/C.
Q: Can we visit your company and factory?
A: Yes, warmly welcome! We can book the hotel for you before you come to China and arrange our driver to our airport to pick you up when you come.
Contact Person: Anndy