Payment & Shipping Terms:
|Product Name:||4340/34CrNiMo6/EN24/817M40/SNCM439/1.6565 Hot Rolled Steel Bar , High Tensile Steel Bar||Material Grade:||4340/34CrNiMo6/EN24/817M40/SNCM439/1.6565|
|Deliervy Condition:||Annealed/hot Rolled/cold Drawn/quenched & Tempered||Surface:||Black/machined/peeled/polished/turned|
|Certificate:||ISO/MTC/BV/SGS||Process:||LD+LF+VOD+CC+HOT ROLLED+CUT+SLOW COOLING+STRAIGHTENED|
|UT:||100% Ultrasonic According To The Test Standards:SEP1921-84||Shape:||Round Shape|
alloy steel round bar,
hot rolled round bar
4340/34CrNiMo6/EN24/817M40/SNCM439/1.6565 Hot Rolled Steel Bar , High Tensile Steel Bar
Length: as your request:
4340 is a 1.8% nickel - chromium - molybdenum high hardenability high tensile steel - generally supplied hardened and tempered in the tensile range of 930 - 1080 Mpa (condition U) - (Rc 28 - 36).
Characterised by high strength and toughness in relatively large sections.
Pre hardened and tempered 4340 can be further surface hardened by flame or induction hardening and by nitriding.
4340 is used in most industry sectors for applications requiring higher tensile/yield strength than 4140 can provide.
Components for the aircraft, automotive, general engineering industries, Propeller shafts, connecting rods, gear shafts, and other automobile parts, Heavy forgings, Rotors, shafts, discs. Pulley shafts, gears, pins and axles, Heavy-duty axles, shafts, heavyduty gears, spindles, pins, studs, collets, bolts, couplings, sprockets, pinions, torsion bars, connecting rods, crow bars, conveyor parts etc. Used where higher yield and tensile strength than 4140 is required.
5.Process: EAF+LF+VOD+ Rolled +Heat Treatment(optional)
6.Test: Ultrasonic test according to SEP 1921-84 3Cc
Heat to 800 oC - 850 oC, hold until temperature is uniform throughout the section and cool in furnace.
Flame or Induction Hardening
4340 hardened and tempered bar can be further surface hardened by either the flame or induction hardening methods resulting in a case hardness in excess of Rc 50. Parts should be heated as quickly as possible to the austenitic temperature range (830 oC - 860 oC) and required case depth followed by an immediate oil or water quench, depending upon hardness required, workpiece size/shape and quenching arrangements.
Following quenching to hand warm, most components should be tempered between 150 oC - 200 oC to remove quenching stresses in the case. This will have little effect on case hardness.
Heat to 830 oC - 860 oC, hold until temperature is uniform throughout the section, soak for 10 - 15 minutes per 25 mm section, and quench in oil, water, or polymer as required.
*Temper immediately while still hand warm.
4340 hardened and tempered bar can also be successfully nitrided, giving a surface hardness of up to Rc 60. Nitriding is carried out at 490 oC - 530 oC, followed by slow cooling (no quench) reducing the problem of distortion. Parts can therefore be machined to near final size, leaving a grinding allowance only. The tensile strength of the core is usually not affected since the nitriding temperature range is generally below the original tempering temperature employed.
N.B. Nickel is inert to the action of nitrogen and in general resists its diffusion into steel. This can result in lower case hardness or longer nitriding cycle times for steels containing nickel such as 4340.
Heat to 600 oC - 650 oC, hold until temperature is uniform throughout the section, soak for 1 hour per 25 mm of section, and cool in still air.
Re-heat to 450 oC - 660 oC as required, hold until temperature is uniform throughout the section, soak for 1 hour per 25 mm of section, and cool in still air.
N.B. Tempering should be avoided if possible within the range 250 oC - 450 oC due to temper brittleness.
Notes on Heat Treatment
Heating temperatures, rate of heating, cooling and soaking times will vary due to factors such as work piece size/shape also furnace type employed, quenching medium and work piece transfer facilities etc..
Contact Person: Neya
Product name: 826M40 Hot Rolle Steel Bar,Alloy Steel Round Bar With Peeled& Turned Surface, Size 10-350mm, Quenched & Tempered
Material grade: X9940/EN26/40NiCrMo10 4/DIN1.6745/826M40
Delivery condition: hot rolled/cold drawn/annealed/quenched&temperd
Surface condition: black surface/peeled/polished/turned/rough turned